Washing machine manufacturers have done a remarkable job by incorporating a feature that allows users to view error codes directly on the display. This advancement is achieved without the need for specialized diagnostic equipment or specific diagnostic programs. It’s incredibly convenient; in the event of a washer breakdown, you know exactly which error has occurred and what it signifies. With this knowledge at your disposal, you can autonomously tackle certain operational glitches once you’ve interpreted the code.
Breakdowns can range from simple to complex, making the use of error codes exceptionally practical. Listing all appliance manufacturers would be excessively tedious. We’d like to introduce you to a guide featuring the top five leading washing machine manufacturers in the USA.
LG Washing Machine Error Codes and Solutions
AE (А0Е)
Auto shutdown code. The equipment suddenly stops washing
The error occurs when the float sensor is triggered. The washing machine needs to be checked for leaks. To do this, all components and connections that come into contact with water are inspected.
dE
Loading door not closed
– Try closing the loading door again.
– Check the functionality of the loading door lock.
– Inspect the controller.
E1
Water detected in the drip tray
– Check the washing machine units for leaks.
IE
Exceeded water filling wait interval (more than 4 minutes) – water is not entering the drum or is entering very slowly.
– Check the water pressure in the plumbing, inspect the condition of the tap.
– Inspect the pressure switch.
– Check the inlet solenoid valve.
PE
Prolonged water filling time (more than 25 minutes to the minimum mark). This error also occurs with excessively fast tank filling
– Check the water pressure in the plumbing (it may be too low or excessive).
– Inspect the pressure switch.
tE
Temperature sensor malfunction
– Check the temperature sensor and its circuits for breaks or short circuits.
– Inspect the controller.
SE
Hall sensor malfunction. This error is typical for machines with a direct drive
– Inspect the Hall sensor and its connecting circuits.
CE
Motor overload in the washing machine
– Adjust the amount of laundry in the drum – excess weight causes overload.
– Check the functionality of the motor and controller.
– Inspect the drum for shaking (for models with direct drive).
FE
Water tank overflow – the pressure switch signals high water level
– Check the water level sensor.
– Inspect the functionality of the inlet valve (it may get stuck in the open state).
– Check the controller’s functionality.
HE
Heating element malfunction
– Check the functionality of the heating element.
– Inspect the power circuits.
OE
Exceeded water draining wait interval (more than 5 minutes) – water is not draining or is draining very slowly
– Check the drainage system’s passage.
– Inspect the pressure switch and the controller.
UE
Imbalance error
– Check the motor drive and the controller.
– Manually redistribute the laundry in the drum.
E3
Loading error
– Check the controller’s functionality.
LE
Loading door lock malfunction
– Possibly low voltage in the power supply.
– Inspect the motor and the controller.
Whirlpool Washing Machine Error Codes and Solutions
F01 (F13, FH)
The washing machine does not fill with water or there is not enough water
– Check for water in the pipes and water pressure.
– The machine tap should be fully open.
– Ensure there is no siphon effect.
– Clean the filter mesh.
– Possible causes of the breakdown: malfunctioning pressure sensor, electromagnet valve, or control module.
F03 (FP)
The washing machine does not drain water or the liquid drains too slowly
– You selected a mode without water drainage. Change the mode and repeat the wash.
– Clean the drain filter and hose.
– Other causes of the breakdown: faulty pressure switch, pump, burnt controller contacts, or clogged pipes.
F05
The temperature sensor has failed
– Wiring fault or with the coefficient sensor. Rectify the break and replace the part.
F07
Engine control circuit malfunction
– The problem is in the operation of the motor control board – it is necessary to replace the burnt triac or thyristor of the control board.
– The electronic controller is broken – it needs to be repaired or the SMA electronic controller needs to be replaced.
F09
The washing machine constantly fills with water, causing overflow
– Change the detergent and/or reduce the dosage.
– Clean or replace the water level sensor.
– Replace the broken solenoid valve.
– Controller repair.
F11 (F19)
Power system malfunctions
The wash cycle cannot start due to low voltage. After resolving this issue, the code will disappear from the display.
F16 (F20, F21)
Problem with the central board
– Perform a contact check.
– Replace the non-working sections of the board.
– Replace the board entirely.
F22
problem with the heating element or clogging of the dispenser
– The heating element may have shorted to the body or burnt out. The possibility of damaged wiring or a faulty thermal regulator should not be ruled out. Remove the dispenser and rinse it with hot water.
F24
The system has detected an overflow but was unable to drain the water
– The issue lies with the pressure switch, which needs replacement.
F27
The drum of the washing machine spins in only one direction
– Replacement of the reverse relay is required.
F31
Software error
– Check the internet connection.
– Contact Whirlpool technical support.
FDU
The washing machine does not close or open
– Close the door more tightly.
– Make sure no foreign objects are stuck in the lock.
F02 (FA)
The system believes that the washing machine is leaking
– No visible signs of leakage? Turn off the washing machine for 10 minutes.
– Incorrect installation. Check the inlet and drain hoses.
– Clamps have loosened or come off – they need to be tightened.
– Another possible causes of the breakdown: worn-out gasket, tank leak, or bearing seal.
F04
The heating element does not heat the water in time for the end of the cycle, or the washing machine does not heat the water at all
Short circuit in the heating unit, faulty thermal regulator, or heating element. Needs fixing of the break, replacement of the pressure switch, or the heating element itself.
F06
The module does not receive a response from the tachometer, and the washing machine does not spin during the spin cycle
– There is too much laundry in the drum, causing imbalance. Divide the volume of items into two loads and repeat the cycle.
– The tachometer circuit needs checking.
– If the washing machine does not move at all, this error may indicate a motor malfunction or a drive belt that has slipped or torn.
F08 (F12)
Heating element burnt out
– The heating element has burned out or there is a break in the wiring – install a new heating element, tighten the contacts, restore the integrity of the wiring.
– The protective pressure switch is broken – replace it with a new, working pressure switch.
– A malfunction has occurred in the electronic controller – try replacing the burnt out parts on the controller board or replacing the entire controller assembly.
F10 (F15)
Problems with the motor’s operation
The triac on the control module is faulty, or the problem is in the motor itself.
F14
Microprocessor error
– Turn off the washing machine for 10 minutes.
– Firmware of the module is required or its replacement.
F18 (Fod, Sud)
There is too much foam in the washing machine, activating the sensor that blocks the washing machine’s operation
– Reduce the amount of detergent. Hand washing detergent produces too much foam, making it unsuitable for the automatic machine.
F23
The control board receives simultaneous signals indicating that the tank is both full and empty
– Such a malfunction is often related to the water level sensor. Cleaning the pressure switch tubes or replacing it.
– In rare cases, control module repair may be necessary.
F26
The motor is not functioning
– Unlike other codes that indicate motor operation issues, this code indicates a problem with the control board. There is no communication with the motor.
F28
The motor is rotating too slowly
– Need to replace the stator relay.
FDL
The door lock device (DL) has malfunctioned
– Repair of the washing machine door and replacement of the DL is required.
bdd
The drum flaps are open (applies to models with top loading)
– Press the [RESET] button for 3 seconds.
– Open the door and close the drum flaps.
– If the error persists, contact the service center.
Samsung Washing Machine Error Codes and Solutions
5E, 5C, E2
Water does not drain from the machine
– Drain hose is clogged or Blockage in the sewage system or Hoses inside the machine are clogged or Clogged drain pump filter.
– Bent or pinched drain hose.
– The drain pump is not working.
– Water inside the machine froze (the machine was stored at subzero temperatures).
4E, 4C, E1
Water does not fill the machine
– Water supply valve for the machine is closed or there is no water in the house.
– Bent or pinched inlet hose.
– Inlet filter mesh is clogged.
– “Aqua Stop” inlet hose protection has been activated.
SUD, 5D (SD)
Too much foam in the drum
– Incompatible or poor-quality detergent was used.
LE, LC, E9
Water is draining spontaneously from the machine
– Drain hose is lying low.
– Drain hose is incorrectly connected to the sewage system.
– There is a hole or crack in the tank from which water is leaking.
UC, 9C
Unstable voltage in the power supply (too low or high)
– Machine is supplied with voltage below 100 +/- 4 Volts, or above 100 +/- 4 Volts for more than 30 seconds.
LE1, LC1
Water has entered the machine’s bottom
– Drain filter is leaking (not tightly closed or damaged).
– Water is leaking from the powder bunker (container).
– Internal connecting hoses or drain hose are leaking.
– Water is leaking from the door (the seal is damaged).
0E, 0F, 0C, E3
There is too much water in the machine
– The drain hose is incorrectly connected to the sewage system.
– The water inlet valve is stuck in the open state.
BE, BE1, BE2, BE3, BC2, EB
Buttons/button on the control panel are not working
– Plastic buttons on the control panel are sticking.
CLB, Cb, “_ _ _”
“Calibration” mode is activated
– “Calibration” mode is activated.
H1, H2, HE, HE1, HE2, HC, HC1, HC2, E5, E6
Water does not heat up
– Machine incorrectly connected to the power supply.
– Washing heating element is not working.
– Drying heating element is not working.
4C2
Hot water is filling the machine – above 50 °C
The inlet hose is connected to the hot water tap.
UE, UB, E4
The machine cannot evenly distribute items in the drum
– Laundry has bunched up or twisted together.
– Too few items in the machine: one or two.
– Too much laundry in the machine.
3E, 3E1, 3E2, 3E3, 3E4, 3C, 3C1, 3C2, 3C3, 3C4, EA
The motor is overloaded, blocked by a foreign object, or broken.
– Motor overload due to a large amount of laundry.
– Motor is not working.
DE, DE1, DE2, DC, DC1, DC2, ED
The door of the hatch is not closed
– The hatch door is not tightly closed.
– The hatch door locking mechanism is not working.
TE, TE1, TE2, TE3, TC, TC1, TC2, TC3, TC4, EC
No signal from the temperature sensor
– The sensor or its wiring is damaged.
1Е, 1C, E7
No signal from the water level sensor
– The sensor or its wiring is damaged.
A0, A1, A2, A3, A4, A5 – … – A9, B0, C0, D0, E0
Factory test mode is activated.
– Factory test mode is activated.
PoF
Power was turned off during the wash (error appears after the power is restored)
– Power was turned off during the wash.
Maytag Washing Machine Error Codes and Solutions
L
Lid lock malfunction
– Repair the mechanical part, install a new lock solenoid, or completely replace the lock.
– Fix the lock contacts, replace faulty sections.
– Check and tighten the panel contacts, strengthen the connections in the connectors, or completely replace the panel.
1E
Malfunction in the lid lock control system
– The lid lock control unit has malfunctioned – repair or fully replace the unit.
– There is an internal defect in the control panel – inspect and replace the Maytag washing machine control panel.
8E
Motor relay circuit malfunction
– The motor relay control coil has failed – replace the washing machine coil.
– There is a break in the control module-motor circuit – service the motor contacts, identify and replace the faulty wire harnesses.
– There are defects in the operation of the control panel – test the circuits operating on the control panel, eliminate breaks, and if necessary, completely replace the Maytag washing machine control panel.
D08 (D11)
Sprayer problem
– Repair or replace the sprayers.
– The problem may also lie in the control module.
D13
Water overheating
The issue may be in the control module or the temperature sensor.
U
Uneven distribution of laundry in the drum (Manual intervention is required)
– Imbalance has occurred in the switch on the control panel – repair or replace the switch.
– The control panel does not provide stable operation of control and monitoring elements – replace the Maytag washing machine control panel.
6E
Error in the washing machine water heating system
– The water temperature sensor in the washing machine tank has malfunctioned – replace the Maytag washing machine thermistor.
– There is a break in the heating system control circuit – inspect the wire harnesses, tighten the connectors, and if necessary, replace the faulty section.
– There is a defect in the operation of the control panel – inspect the panel, service the contacts, and if necessary, replace the panel completely.
9E
Door lock failure
– Repair the mechanical part or completely replace the lock.
– Fix the lock contacts, replace faulty sections of the Maytag washing machine wiring.
– There are faults in the door switch – service the contacts and if necessary, completely replace the switch.
– The control panel does not provide stable operation of control and monitoring elements – replace the control panel.
D12
Leakage in the drain hose
Replace the drain hose in the washing machine.
D14
Problem with the drain hose connection or the filter clogged with debris
The washing machine cannot properly fill or drain water. Replace the inlet hose and clean the drain filter.
General Electric (GE) Washing Machine Error Codes and Solutions
IE
Pressure switch malfunction (water overflow or insufficient filling)
– Check the pressure switch hose for clogs.
– Rinse the hose under running water.
– Check the pressure switch by blowing into the tube. If faulty, install a new component.
E
water drainage problems (drain pump or electronic control unit)
– Inspect and clean the pump filter, the tank-to-pump pipe, and the hose.
– Check and replace the drain pump in case of a breakdown.
– Test the main module. Replace if necessary.
UE
Imbalance in the washing machine (excessively large load of laundry)
– Open the door and manually redistribute the laundry evenly.
– Remove half of the items from the drum.
7E
Water intake system issues (There is a clog or Incorrect connection)
– Check the correctness of the connection.
– Inspect the intake hose and valve filter during clogging. Rinse under running water.
– Replace the inlet valve.
dE
The door of the hatch is not tightly closed
– Inspect the lock for debris and clean it.
– Check the side hinges. If they are misaligned, tighten them.
– Install a new door lock mechanism (door lock).
OE
Too much water in the tank
– Replace the inlet valve.
– Install a functioning pressure switch.
Conclusion
With the increasing reliance on washing machines in our daily lives, it’s imperative for repair technicians to be well-versed in decoding error codes. By understanding the nuances of each error message and the corresponding troubleshooting solutions, technicians can expedite the repair process and ensure customer satisfaction. Stay equipped with this comprehensive guide and navigate through the intricacies of washing machine malfunctions with confidence and precision.
If you need help with your appliance, then you can look into the service section – Repair service In Tucson.